WN RTJ Class 900 / 1500 Forged Ball Valve RFQ Guide

Technical guide · Supreme Valves India · Updated 2026-11-17

Direct answer: A WN RTJ Class 900 / 1500 ball valve RFQ must lock size, ASME class, weld-neck RTJ facing, body MOC (often A105N or stainless), floating vs trunnion, bore, operator, fire-safe requirement, and test basis. Missing any of these produces wrong flanges, wrong torque packages, or soft-seat designs that cannot hold the class.

Recent project enquiries for forged carbon-steel ball valves with weld-neck RTJ ends at Class 900 and Class 1500 show the same pattern: quantity is clear, construction detail is not. This guide is the checklist we use before pricing.

What WN RTJ actually specifies

Floating vs trunnion (do not leave blank)

Topic Floating Trunnion
Typical sizes on HP RFQs1/2 inch to about 2 inch (project-dependent)3 inch / 4 inch and up on Class 900 packages
OperatorLever commonGearbox + handwheel often mandatory
Seat / stem loadsSeat-supported ballTrunnion bearings carry side load

If the tag list says “trunnion, gear” on DN80/DN100 Class 900, do not accept a floating lever alternative without written buyer approval.

Material notes (A105N and beyond)

ASTM A105N forged carbon steel is common for body/end pieces on hydrocarbon utility packages. Confirm NACE / sour service separately — A105N alone is not a NACE certificate. For stainless or duplex HP balls, state the exact UNS / ASTM grade on the PO.

Soft seat vs metal seat at Class 900+

Virgin PTFE / RPTFE soft seats are widely offered on lower classes. At Class 900 / 1500, confirm temperature, differential pressure, and whether the datasheet allows soft seat or requires metal seat / PEEK / Nylon systems. Cold flow of PTFE under sustained high pressure is a real failure mode.

Fire-safe and antistatic

Hydrocarbon RFQs often expect fire-safe design practice (API 607 / ISO 10497 type-test pedigree for the product family) plus antistatic features. Say whether you need a type-test certificate for the exact size/class or design-in-accordance. Those are different commercial scopes.

RFQ line checklist (copy into your enquiry)

  1. NPS / DN and quantity
  2. ASME Class 900 or 1500
  3. Ends: WN RTJ per ASME B16.5 (state ring number if known)
  4. Body / ball / stem MOC
  5. Floating or trunnion; full bore or reduced bore
  6. Operator: lever / gear / actuator
  7. Seat material and fire-safe requirement
  8. Design / test standards (API 6D practice, ASME B16.34, API 598)
  9. Delivery basis and documentation (EN 10204 3.1 MTC, ITP)

Supreme Valves India manufactures and quotes forged and cast ball valves from Ahmedabad for domestic GST and export terms. Send the tag list as-is — we will flag class, facing, and floating/trunnion conflicts before production. Related: RF vs RTJ, trunnion vs floating, RFQ form.

Frequently asked questions

What does WN RTJ mean on a ball valve RFQ?

WN means weld-neck flanged ends. RTJ means ring-type joint facing (groove for a metal ring gasket), common on Class 900 and Class 1500 hydrocarbon and high-pressure lines. The valve flange must match ASME B16.5 facing and ring groove for the stated class.

When should Class 900 move to Class 1500?

Follow the piping class and ASME B16.34 pressure-temperature rating for the body material at design temperature. Do not upsize class only for marketing. If the line list is Class 1500, quote Class 1500 ends, wall, and test pressures.

Floating or trunnion for 3 inch and 4 inch Class 900?

Small sizes are often floating; larger high-pressure lines commonly need trunnion-mounted designs with gear or actuator. State floating vs trunnion, bore (full/reduced), and operator on every line.

Related products & guides

Request valve RFQ →