API 608 vs API 6D Ball Valve Chart

Updated 2026-11-08 · Screening reference for engineers & contractors.

Direct answer · Floating vs pipeline ball standards

API 608 is the usual citation for process / floating (and many plant) metal ball valves under ASME B16.34. API 6D is the usual citation for pipeline ball (often trunnion), gate and check valves with 6D design/test/documentation. Match the standard to the service — do not put API 6D features on a soft-seat utility ball RFQ unless required.

RFQ from this chart — size · class · API 608/6D · floating/trunnion · ends · qty.

Contact / RFQ WhatsApp

Side-by-side comparison

TopicAPI 608API 6D
Typical serviceProcess plant / refining / petrochem on/offPipeline transmission / gathering (as scoped)
Ball supportOften floating; trunnion when specifiedOften trunnion-mounted (large DN / high ΔP)
Size / classASME Class per B16.34; plant sizesPipeline sizes / pressure designations per 6D
Pressure basisASME B16.34API 6D + referenced rating practice
EndsFlanged, SW, BW, threaded as allowedFlanged, BW, hub — pipeline practice
BoreFull / reduced per datasheetFull-opening emphasis for pigging when required
Fire safeOften API 607 / ISO 10497 when specifiedFire test / fire-safe design as specified in package
TestingCommonly API 598API 6D test requirements
Features often citedSoft/metal seat, antistatic, firesafeDBB, DIB, cavity relief, stem extension, etc.
DocumentationMTC / ITP per purchaserHeavier 6D quality / traceability expectations

Floating vs trunnion (engineering screen)

ConstructionTypical useStandard lean
Floating ballSmall–medium process, seat-loaded sealAPI 608 + B16.34
Trunnion ball (plant)Larger DN / higher ΔP in process unitsAPI 608 or purchaser trunnion spec + B16.34
Trunnion ball (pipeline)Mainline / piggable / ESDAPI 6D
Soft seat PTFE/RPTFEClean fluids, tight shutoffState seat material + fire-safe if needed
Metal seatHigh temp / abrasive / firesafe metalState leakage class expectation

Size thresholds for floating→trunnion vary by class and manufacturer design. Put ΔP, size and preferred construction on the RFQ rather than assuming a cutover NPS.

What to write on the RFQ

FieldExample
Product standardAPI 608 or API 6D
ConstructionFloating / trunnion; 2-pc / 3-pc / fully welded
RatingASME Class 150/300… or 6D pressure designation
EndsRF / RTJ / BW / SW
BoreFull or reduced
Seat / fire-safeRPTFE + API 607 (if required)
TestAPI 598 or API 6D (not both mixed)
ActuationLever / gear / DA / SR — see actuation charts

Related: API 598 vs API 6D testing · gate standards chart · test pressure chart.

FAQ

Is API 608 only for floating balls?

API 608 addresses metal ball valves for petroleum, petrochemical and allied industries — commonly floating (and some trunnion) process constructions with ASME B16.34 ratings. Pipeline transmission packages usually cite API 6D instead.

When must I use API 6D?

When the valve is a pipeline valve under API 6D scope (typically larger trunnion-mounted balls/gates/checks for transmission and similar services) with 6D testing, documentation and feature requirements (DBB, cavity relief, etc. as specified).

Which test standard goes on the PO?

API 608 process balls often test to API 598. API 6D valves follow API 6D test clauses. Do not mix acceptance criteria — see API 598 vs API 6D testing notes on the site.

Related charts