What is the temperature of saturated steam at 7 kg/cm²g?
Approximately 170 °C (rounded). Use the table on this page for nearby pressures and confirm exact Tsat from your project steam tables before heat-balance or Class selection.
Updated 2026-11-08 · Rounded steam-table screening values. Verify against your project steam tables / ASME steam properties before heat balances.
Direct answer · Saturated steam P-T
Steam valve RFQ — size · Class · MOC · ends · design P/T · sat/superheat · qty.
Contact / RFQ WhatsAppContractors and plant engineers open a saturated steam P-T chart when converting nameplate boiler pressure into expected line temperature, when checking whether Class 150 still has margin at temperature, and when estimating steam density for globe-valve Cv. The tables below are dense enough for daily desk use; they remain screening data, not a certified steam table extract.
| P (kg/cm²g) | P ≈ (bar g) | Tsat ≈ (°C) | Tsat ≈ (°F) | Typical plant use |
|---|---|---|---|---|
| 0.5 | 0.5 | 112 | 234 | Very LP utility |
| 1.0 | 1.0 | 120 | 248 | LP process / HVAC steam |
| 1.5 | 1.5 | 128 | 262 | LP distribution |
| 2.0 | 2.0 | 134 | 273 | LP process |
| 2.5 | 2.5 | 139 | 282 | LP process |
| 3.0 | 2.9 | 143 | 290 | LP header |
| 3.5 | 3.4 | 148 | 298 | Common Indian LP |
| 4.0 | 3.9 | 152 | 305 | LP / MP boundary |
| 5.0 | 4.9 | 159 | 318 | MP light |
| 6.0 | 5.9 | 165 | 329 | MP light |
| 7.0 | 6.9 | 170 | 338 | Very common plant steam |
| 8.0 | 7.8 | 175 | 347 | MP process |
| 9.0 | 8.8 | 180 | 355 | MP process |
| 10 | 9.8 | 184 | 363 | MP header |
| 12 | 11.8 | 192 | 377 | MP header |
| 14 | 13.7 | 198 | 388 | MP / HP light |
| 16 | 15.7 | 204 | 399 | MP steam |
| 17.5 | 17.2 | 207 | 405 | Classic Indian MP |
| 20 | 19.6 | 214 | 417 | MP / HP |
| 21 | 20.6 | 216 | 421 | HP light |
| 25 | 24.5 | 226 | 439 | HP process |
| 30 | 29.4 | 235 | 455 | HP process |
| 35 | 34.3 | 244 | 471 | HP |
| 40 | 39.2 | 252 | 485 | HP boiler / power |
| 50 | 49.0 | 265 | 509 | HP |
| 60 | 58.8 | 277 | 530 | HP |
| 64 | 62.8 | 281 | 538 | HP Class 600 region |
| 80 | 78.5 | 296 | 565 | Power / HP |
| 100 | 98.1 | 311 | 592 | Power / HP |
Values rounded for desk screening. Absolute pressure = gauge + local atmospheric (~1.033 kg/cm² at sea level). Correct for altitude on vacuum / LP condenser work.
Steam mass flow (kg/h) converts to volumetric flow using specific volume v (m³/kg) or density ρ = 1/v. Use inlet conditions for capacity; check critical pressure ratio for choked flow.
| P (kg/cm²g) | Tsat ≈ (°C) | ρ steam ≈ (kg/m³) | v ≈ (m³/kg) | hf ≈ (kJ/kg) | hfg ≈ (kJ/kg) |
|---|---|---|---|---|---|
| 1 | 120 | ~1.1 | ~0.88 | ~505 | ~2200 |
| 3.5 | 148 | ~2.4 | ~0.42 | ~625 | ~2110 |
| 7 | 170 | ~4.1 | ~0.24 | ~720 | ~2050 |
| 10 | 184 | ~5.5 | ~0.18 | ~780 | ~2000 |
| 17.5 | 207 | ~8.8 | ~0.11 | ~880 | ~1920 |
| 25 | 226 | ~12 | ~0.083 | ~960 | ~1850 |
| 40 | 252 | ~18 | ~0.055 | ~1090 | ~1710 |
| 64 | 281 | ~28 | ~0.036 | ~1230 | ~1540 |
| 100 | 311 | ~43 | ~0.023 | ~1400 | ~1320 |
Enthalpy and density figures are approximate mid-range values for orientation. Latent heat hfg falls as pressure rises — important for trap condensate load estimates.
| Task | Take from chart | Then open |
|---|---|---|
| Isolation Class pick | Tsat at design P | IBR steam rating / B16.34 chart |
| Globe Cv estimate | ρ or v at inlet | Valve Cv table + steam formula |
| Trap selection | ΔT vs ambient / load | Steam trap selection chart |
| Packing / gasket | Tsat or Tsuperheat | Gasket / trim charts |
| Blowdown flash | Boiler P → flash T | Blowdown valve chart |
| P absolute (bar a) | ≈ mmHg vacuum (sea level) | Tsat ≈ (°C) | Note |
|---|---|---|---|
| 0.05 | ~725 | ~33 | Deep condenser vacuum |
| 0.10 | ~685 | ~46 | Condenser / LP turbine exhaust region |
| 0.20 | ~610 | ~60 | Warm vacuum |
| 0.50 | ~385 | ~81 | Deaerator / LP heater region depends on plant |
| 1.013 | 0 (atm) | 100 | Atmospheric boiling |
Condensate and vacuum drain valves see low absolute pressure but can still see high temperature during air-inleak or startup. State vacuum service and design temperature separately on the RFQ.
| From | To | Factor (approx.) |
|---|---|---|
| 1 kg/cm² | bar | × 0.981 |
| 1 kg/cm² | kPa | × 98.1 |
| 1 kg/cm² | psi | × 14.22 |
| 1 bar | kPa | × 100 |
| °C | °F | × 1.8 + 32 |
| Gauge → absolute | — | + local atm (~1.033 kg/cm²) |
Approximately 170 °C (rounded). Use the table on this page for nearby pressures and confirm exact Tsat from your project steam tables before heat-balance or Class selection.
Convert steam mass flow to volumetric flow using specific volume (or density) at the inlet P-T, then apply the steam Cv equation from the purchaser standard. Check outlet pressure for critical drop and noise. Pair with the Cv chart and Class P-T rating.
No. Superheat raises temperature above Tsat at the same pressure. Valve MOC and packing must follow the higher design temperature, not the saturation temperature alone.
1 kg/cm² ≈ 0.981 bar ≈ 98.1 kPa. Many Indian datasheets still use kg/cm²g. Convert carefully when mixing SI (bar/MPa) flange tables with older boiler nameplates.
Yes. Send size, Class/PN, MOC, ends, design P, design T (sat or superheat), IBR if applicable, and quantity via contact.html.
Screening properties for 2026 engineering use. Confirm critical energy balances against project-approved steam tables and current ASME/IBR editions.