Valves for Offshore Platforms: Types and Materials by System
Technical guide · Supreme Valves India · Updated 2026-11-21
An offshore platform uses the same valve types as an onshore plant, but the material choices are different. Seawater, salt-laden air, limited space and weight, and long distances from a workshop all push specifications towards corrosion-resistant alloys and compact designs. This guide goes through the main systems on a platform and the valves normally specified for each.
Valves by platform system
| System | Usual valve types | Usual body materials |
|---|---|---|
| Firewater ring main and deluge | Butterfly, gate, dual plate check, deluge valves | Nickel aluminium bronze (C95800), super duplex, titanium |
| Seawater lift and cooling | Butterfly, ball, dual plate check, strainers | Nickel aluminium bronze, super duplex, 6Mo stainless |
| Hydrocarbon process: manifolds, separation, export | Trunnion ball, gate, check, globe | Carbon steel, low-temperature carbon steel, duplex, alloy-clad carbon steel |
| Emergency shutdown and blowdown | Actuated ball valves, fail-safe | As the process line, fire-tested design |
| Produced water and water injection | Ball, butterfly, check, control valves | Duplex, super duplex |
| Chemical injection and instrument lines | Needle valves, manifolds, double block and bleed | SS316, 6Mo, alloy 625 depending on the chemical |
| Utilities: instrument air, nitrogen, diesel, potable water | Ball, gate, globe, check | SS316, bronze, carbon steel |
Each operator has its own piping material classes, so treat this table as a starting point and follow the project specification.
Why seawater systems use NAB, super duplex or titanium
Standard SS316 suffers pitting and crevice corrosion in warm, stagnant or chlorinated seawater, particularly under gaskets and in dead legs. Firewater mains are the worst case, because the water sits still for long periods. Specifications therefore move to materials with better resistance:
- Nickel aluminium bronze (ASTM B148 C95800). Good resistance to seawater and to marine fouling, and widely used for firewater and cooling water valves.
- Super duplex stainless steel. High strength and a pitting resistance equivalent number (PREN) above 40. Used where pressure or mechanical strength rules out bronze.
- 6Mo austenitic stainless and titanium. Used for the most demanding duties and for chlorinated or hot seawater.
Mixing metals matters as much as choosing them. A bronze valve in a super duplex or titanium line can corrode galvanically, so the valve and pipe materials should be selected together.
Hydrocarbon process valves
- Trunnion mounted ball valves to API 6D are the standard isolation valve, often full bore and with double block and bleed or double isolation seats.
- Sour service. Where hydrogen sulphide is present, materials and hardness must meet NACE MR0175 / ISO 15156.
- Fire testing. Soft-seated valves in hydrocarbon service are specified as fire-tested to API 607 or API 6FA.
- Low temperature. Blowdown and gas lines can reach low temperatures on depressurisation, which calls for low-temperature carbon steel or stainless steel with impact testing.
- Fugitive emissions. Stem sealing is often specified to ISO 15848.
Emergency shutdown valves
Shutdown and blowdown valves are actuated ball valves with spring-return or hydraulic fail-safe actuators. They are specified with a required stroke time, a fail position, partial-stroke testing if needed, and a safety integrity level for the whole loop. The valve, actuator and solenoid have to be assessed as one assembly, so state the requirement on the RFQ and ask what documentation will be supplied.
Space, weight and maintenance
- Compact designs. Wafer and lug butterfly valves and dual plate wafer check valves replace flanged gate and swing check valves where the specification allows, saving weight and length.
- Top-entry valves can be repaired in line, which avoids cutting out a welded valve offshore.
- Coating. Carbon steel valves need an offshore paint system. Projects in the North Sea commonly call for NORSOK M-501.
- Spares. Order seat and seal kits with the valves. Getting a small part to a platform can take longer than the repair.
Documents that offshore buyers ask for
- EN 10204 3.1 material certificates, or 3.2 with third-party witnessing on critical items.
- Positive material identification on alloy parts.
- Pressure test certificates to API 598 or API 6D.
- Fire test and fugitive emission type-test certificates where specified.
- NACE compliance statements for sour service.
- Manufacturer qualification for special alloys where the project requires it, for example to NORSOK M-650.
- Painting records and final inspection reports.
Requirements vary widely between operators. Send the piping material class and the valve datasheets with the enquiry, and we will confirm line by line what we can supply and which documents come with it.
RFQ checklist
- System and fluid: seawater, firewater, hydrocarbon, produced water, utility.
- Size, pressure class and end connection.
- Body, trim and seat materials from the piping class.
- Design pressure and temperature, including minimum design temperature.
- Sour service, fire-tested design and fugitive emission requirements.
- Operation: lever, gear or actuator, with fail position and stroke time for shutdown valves.
- Coating system, inspection level and document list.
Frequently asked questions
What valves are used on offshore platforms?
Trunnion ball valves for hydrocarbon isolation and shutdown, butterfly and dual plate check valves for seawater and firewater, gate, globe and check valves on process and utility lines, and needle and double block and bleed valves on instrument and chemical injection lines.
Which material is used for offshore firewater valves?
Nickel aluminium bronze (C95800) and super duplex stainless steel are the most common, with titanium on some projects. Standard SS316 is avoided because it pits in stagnant seawater.
Why is SS316 not used for seawater valves offshore?
SS316 suffers pitting and crevice corrosion in warm, stagnant or chlorinated seawater. Nickel aluminium bronze, super duplex, 6Mo stainless and titanium have much better resistance.
Which standards apply to offshore process valves?
API 6D for pipeline and process ball valves, NACE MR0175 / ISO 15156 for sour service, API 607 or API 6FA for fire testing, ISO 15848 for fugitive emissions, and API 598 or API 6D for pressure testing.
What documents do offshore valve buyers require?
Typically EN 10204 3.1 or 3.2 material certificates, positive material identification on alloys, pressure test certificates, fire test and fugitive emission certificates where specified, NACE compliance statements and painting records.