Is CF8M acceptable for seawater valves?
Often not for continuous seawater. 316/CF8M is prone to pitting and crevice corrosion in aerated seawater; prefer NAB, duplex, 254SMO or titanium per system design.
Updated 2026-11-08 · Screening reference for engineers & contractors.
Direct answer · Seawater MOC orientation
| Family | Typical grades | PREN / notes | Where it shows up |
|---|---|---|---|
| NAB | C95800 / ABS Type approval grades | Copper alloy — not PREN logic | Marine firewater, seawater butterfly / check |
| Duplex | F51 / A890 4A (S31803/S32205) | PREN ≈ 35 | Offshore cooling, desal feed |
| Super duplex | F53 / F55 / A890 5A–6A | PREN ≈ 40+ | Higher chloride / critical SW systems |
| 6Mo / 254SMO | UNS S31254 / similar | High PREN austenitic | Desal, high-chloride process |
| Titanium | Gr.2 / Gr.5 wetted | Excellent SW immunity | Severe SW / heat exchanger loops |
| Ni-Cu (Monel family) | M35-1 / N04400 family | Good SW; cost & galvanic care | Selected marine / chemical |
| CF8M / 316 | A351 CF8M / F316 | Often inadequate for continuous SW | Short exposure / splash only if approved |
| Duty | Common first pick | Escalate to | Watch-outs |
|---|---|---|---|
| Ship / platform firewater | NAB or duplex | Super duplex | Stagnation; coating of adjacent CS pipe |
| Seawater cooling (flowing) | Duplex / NAB | Super duplex / Ti | Velocity erosion-corrosion on Cu alloys |
| SWRO high-pressure brine | Super duplex / 254SMO | Titanium | Chlorides + pressure; crevices at seats |
| Desal low-pressure SW | Duplex / NAB | Super duplex | Biofouling; chlorination chemistry |
| Ballast / bilge (marine) | NAB / coated CS (if allowed) | Duplex | Owner + class society list |
| Heat exchanger SW side | Ti / Cu-Ni / SDSS | Ti | Galvanic couple with tube material |
| Chlorinated seawater | Duplex / SDSS / SMO | Ti | Free chlorine residuals attack some alloys |
| Issue | Why it matters on valves | RFQ action |
|---|---|---|
| CS pipe + stainless valve | Galvanic attack on carbon steel | State insulation / coating / spool MOC |
| NAB + stainless fasteners | Couple in wet SW | Specify compatible bolting / isolation |
| Crevice at wafer seats | Localised pitting under gasket/seat | Prefer resistant MOC; avoid stagnant traps |
| High velocity | Erosion of Cu alloys | Velocity limit + duplex/Ti preference |
| “SS” only on BOQ | May be read as CF8M — often wrong | Write duplex / NAB / SMO / Ti explicitly |
Screening disclaimer: Seawater corrosion is system-specific (temperature, oxygen, chlorination, velocity, stagnant legs). This chart does not replace owner corrosion standards or class-society material lists. Confirm final MOC with the project corrosion engineer.
| Field | Why |
|---|---|
| Seawater / brine / firewater | Sets corrosion family |
| Preferred MOC (NAB / duplex / SMO / Ti) | Avoids CF8M default |
| Temperature · chlorination · velocity notes | Alloy escalation |
| Valve type · size · Class/PN · ends | Construction |
| Class society / owner notes | Marine compliance |
| Quantity + delivery port | Export offer |
Often not for continuous seawater. 316/CF8M is prone to pitting and crevice corrosion in aerated seawater; prefer NAB, duplex, 254SMO or titanium per system design.
Both appear on marine firewater specs. NAB is traditional for seawater valves; duplex is common on newer offshore lists. Follow the class society / owner material philosophy.
Yes when media (seawater/brine), preferred family (NAB/duplex/SMO/Ti), size, rating and ends are stated on contact.html.