When should WC6 replace WCB?
When design temperature exceeds the practical WCB / carbon-steel band for the required pressure, or when the purchaser pipe material is 1¼Cr–½Mo.
Updated 2026-11-08 · Screening reference for engineers & contractors.
Direct answer · WC6 / WC9 / C5 / C12
| ASTM A217 | Nominal chemistry | Forging counterpart | Screening upper band* | Typical service |
|---|---|---|---|---|
| WCB (A216) | Carbon steel | A105 | ≈ 425 °C | Utility steam / process CS |
| WC6 | 1¼Cr–½Mo | A182 F11 | ≈ 550–593 °C | Superheated steam, hot oil |
| WC9 | 2¼Cr–1Mo | A182 F22 | ≈ 550–593 °C+ | Higher steam / hydrocracker feed |
| C5 | 5Cr–½Mo | A182 F5 | ≈ 650 °C class | Refinery hot hydrocarbon |
| C12 | 9Cr–1Mo | A182 F9 | High-temp power | Legacy 9Cr lists |
| C12A | 9Cr–1Mo–V–Nb | A182 F91 | Modern HRSG / main steam | Preferred 9Cr casting today |
*Upper bands are engineering screening only. Allowable pressure drops with temperature per ASME B16.34 Group tables. Always freeze design on the current edition and purchaser P-T curve.
| Condition | Likely move | Also check |
|---|---|---|
| Design temp above WCB P-T for required Class | WC6 or higher | Bonnet gasket / packing temp limit |
| Pipe is P11 / 13CrMo4-5 | WC6 / F11 valves | BW end prep & PWHT |
| Pipe is P22 / 10CrMo9-10 | WC9 / F22 | Hardness / PWHT procedures |
| Hot refinery transfer lines (5Cr pipe) | C5 / F5 | Sulphidation / coking notes |
| Power main steam / HRSG (P91) | C12A / F91 | Do not substitute C12 casually |
| IBR steam service India | Grade per IBR + ASME | IBR documentation on RFQ |
| Item | Screening note |
|---|---|
| Seat / disc | Hardfacing (Stellite family) common on alloy steam valves |
| Stem | 13Cr or high-temp stainless per trim chart |
| Bolting | B7/L7 give way to B16 / high-temp alloy bolting as temp rises |
| Gasket / packing | Graphite / spiral wound — elastomer seats out of range |
| Actuation | Gear / pneumatic with high-temp brackets; confirm ambient at actuator |
| Casting | Forging | EN near-eq. (cast / forge) |
|---|---|---|
| WC6 | F11 | G17CrMo5-5 / 13CrMo4-5 |
| WC9 | F22 | G17CrMo9-10 / 10CrMo9-10 |
| C5 | F5 | 5Cr cast / X12CrMo5 |
| C12A | F91 | GX12CrMoVNbN9-1 / X10CrMoVNb9-1 |
Screening disclaimer: Temperature bands above are orientation aids, not certified allowable temperatures. Final rating is by ASME B16.34 material group, flange Class, wall design and purchaser datasheet. Soft-seat ball valves are rarely suitable for these bands.
| Field | Why |
|---|---|
| Exact grade (WC6 / WC9 / C5 / C12A) | Alloy family & heat treatment |
| Design & operating temperature | P-T confirmation |
| Design pressure / Class | Wall & flange rating |
| Ends (RF / RTJ / BW) | High-temp joints often BW/RTJ |
| Trim / hardfacing notes | Steam cutting / erosion |
| IBR / EN 10204 3.1 / PMI | Documentation package |
When design temperature exceeds the practical WCB / carbon-steel band for the required pressure, or when the purchaser pipe material is 1¼Cr–½Mo.
No. C12A is the modified 9Cr–1Mo–V–Nb grade commonly used for modern high-temperature power service; do not substitute without purchaser approval.
Yes. State grade (WC6/WC9/C5/C12A), design temperature, size, Class, ends and quantity on contact.html.