Pneumatic Actuator Sizing Chart

Updated 2026-11-08 · Screening reference for engineers & contractors.

Direct answer · Pneumatic actuator sizing

Required actuator torque = valve breakaway torque × safety factor, checked at minimum instrument air pressure. Use double-acting (DA) when air is available both ways and fail-safe is not mandatory; use spring-return (SR) for fail-close / fail-open. Typical clean-service factor is 1.25–1.30×; severe service 1.40–1.50×.

RFQ from this chart — size · class/PN · MOC · ends · DA/SR · air bar · qty.

Contact / RFQ WhatsApp

Torque safety factors (screening)

Service conditionFactor × breakawayWhen to use
Clean liquid / gas, ambient, low cycle1.25 – 1.30HVAC, clean utility, soft-seat ball
Steam / hot oil / sticky media1.35 – 1.45Seat swell, packing drag
Dirty / slurry / infrequent stroke1.40 – 1.50Seized-seat risk after long dwell
High ΔP butterfly at large DN1.40 – 1.50Confirm dynamic torque separately
Fire-safe metal seat / high cycle≥ 1.50Per purchaser / SIL envelope

Apply the factor to the governing torque (usually breakaway or seating). Do not reduce factors because catalogue torque “looks generous.”

Double-acting (DA) vs spring-return (SR)

ItemDouble-acting (DA)Spring-return (SR)
Air useAir to open + air to closeAir one way; springs the other
Fail on air lossStays last position (unless lock / dump strategy)Moves to FO or FC spring position
Size / costSmaller for same torqueLarger; spring set must cover end-of-stroke
Typical picksBatch / non-ESD on/offESD, fire water isolation, cooling FO
Critical checkTorque at min air both directionsSpring torque at weakest stroke angle ≥ required × SF
AccessoriesSolenoid, limit switches, positioner optionalSame + confirm FO/FC spring set on nameplate

Air supply notes

Plant air (typical)Sizing note
3.0 – 4.0 bargLow IA — expect larger actuator; verify SR spring tables carefully
4.5 – 5.5 bargCommon instrument air design basis for RFQs
6.0 – 7.0 bargHigher output; still size on min guaranteed, not peak
8+ bargCheck actuator Pmax rating, seals and tubing class
Filtered / dry / oil-freeState dew point / filtration when actuators are indoors critical
Long tubing runsPressure drop + stroke time — note solenoid Cv / boosters if needed

Sizing sequence (desk check)

StepActionOutput
1Get valve breakaway / seating / running torque at design ΔPNm (or in·lb)
2Apply safety factor from table aboveRequired Nm
3Confirm min IA at valve locationbarg
4Select DA or SR + FO/FCDuty
5Match ISO 5211 flange / drive squareF05–F16 etc.
6Add solenoid voltage, LS, positioner, manual overrideAccessories list

Interactive worksheet: pneumatic actuator sizing calculator. Electric vs pneumatic selection: selection matrix.

FAQ

What safety factor should I use for pneumatic actuator sizing?

Clean media, ambient temperature: typically 1.25–1.30× breakaway torque. Dirty, high-temp, high-cycle or sticky seats: 1.40–1.50×. Always size at the minimum guaranteed air pressure.

When do I choose spring-return instead of double-acting?

Choose spring-return (SR) when fail-safe open or closed is required on air failure. Double-acting (DA) needs a solenoid/air lock or volume tank strategy if fail position matters.

What air pressure should I put on the RFQ?

State the minimum instrument air available at the valve (often 4–5.5 barg plant IA). Do not size on the compressor nameplate maximum.

Related charts