What is the Cv of a 2 inch ball valve?
Calculated for a full-bore valve, fully open, a 2 inch (DN50) ball valve has a Cv of about 535 (Kv about 463). A 2 inch reduced-bore valve is much lower. Confirm with the manufacturer's datasheet.
Updated 2026-11-21 · Supreme Valves India · Ahmedabad
A full-bore ball valve has a port the same diameter as the pipe, so when it is open it adds very little resistance. That gives it the highest Cv of the common valve types. The figures on this page are for full-bore valves; a reduced-bore valve of the same nominal size has a much lower Cv.
Quick answer
Calculated Cv for a fully open ball valve: 1" ≈ 125, 2" ≈ 535, 4" ≈ 2,150. Cv is the flow of water in US gallons per minute that gives a 1 psi pressure drop. These are calculated estimates; use the manufacturer's datasheet value for final sizing.
| Size (NPS) | DN | Bore used (in) | K | Cv | Kv |
|---|---|---|---|---|---|
| ½" | DN15 | 0.622 | 0.081 | 40.6 | 35.2 |
| ¾" | DN20 | 0.824 | 0.075 | 74.1 | 64.1 |
| 1" | DN25 | 1.049 | 0.069 | 125 | 108 |
| 1¼" | DN32 | 1.380 | 0.066 | 222 | 192 |
| 1½" | DN40 | 1.610 | 0.063 | 309 | 267 |
| 2" | DN50 | 2.067 | 0.057 | 535 | 463 |
| 2½" | DN65 | 2.469 | 0.054 | 784 | 678 |
| 3" | DN80 | 3.068 | 0.054 | 1,210 | 1,050 |
| 4" | DN100 | 4.026 | 0.051 | 2,150 | 1,860 |
| 5" | DN125 | 5.047 | 0.048 | 3,480 | 3,010 |
| 6" | DN150 | 6.065 | 0.045 | 5,180 | 4,480 |
| 8" | DN200 | 7.981 | 0.042 | 9,290 | 8,040 |
| 10" | DN250 | 10.020 | 0.042 | 14,600 | 12,700 |
| 12" | DN300 | 11.938 | 0.039 | 21,600 | 18,700 |
| 14" | DN350 | 13.124 | 0.039 | 26,100 | 22,600 |
| 16" | DN400 | 15.000 | 0.039 | 34,100 | 29,500 |
| 18" | DN450 | 16.876 | 0.036 | 44,900 | 38,800 |
| 20" | DN500 | 18.812 | 0.036 | 55,800 | 48,200 |
| 24" | DN600 | 22.624 | 0.036 | 80,700 | 69,800 |
Basis: K = 3 × fT for a full-bore ball valve, fully open, with the Crane TP-410 friction factor fT for each size and the Schedule 40 pipe inside diameter as the bore. Values are rounded to three significant figures. Tested values on a manufacturer's datasheet are usually lower, because seat rings, port shape and body geometry add resistance.
K is the resistance coefficient of the fully open valve. Crane Technical Paper 410 expresses it as a multiple of the pipe friction factor fT, which lets one formula cover every size. If you know the actual seat bore of the valve you are buying, put that diameter into the formula instead of the Schedule 40 figure.
Example: water (SG 1.0) at 400 US gpm through a 4" ball valve with Cv 2,150 gives ΔP = (400 ÷ 2,150)² ≈ 0.03 psi. In metric units, 90 m³/h through the same valve (Kv 1,860) gives about 0.002 bar.
Pressure-drop and required-Cv calculator (liquids)
Send line size, class, fluid, flow and allowable pressure drop. We reply with a matched ball valve offer and datasheet.
Contact / RFQ WhatsAppCalculated for a full-bore valve, fully open, a 2 inch (DN50) ball valve has a Cv of about 535 (Kv about 463). A 2 inch reduced-bore valve is much lower. Confirm with the manufacturer's datasheet.
Yes. A full-bore valve has a port equal to the pipe bore. A reduced-bore valve has a smaller port, typically one size down, and a much lower Cv for the same nominal size.
Kv = 0.865 × Cv, and Cv = 1.156 × Kv. Cv is in US gallons per minute at 1 psi drop; Kv is in m³/h at 1 bar drop.
No. V-port and segmented ball control valves have their own Cv tables by opening angle. This chart is for fully open, full-bore isolation valves.
Globe valve Cv chart · Gate valve Cv chart · Butterfly valve Cv chart · Master Cv chart · Cv to Kv conversion · Valve pressure-drop calculator · Ball valves · Quote from Cv sizing
Reference: Crane Co., Technical Paper No. 410, Flow of Fluids Through Valves, Fittings and Pipe. This page is an engineering aid, not a substitute for the valve manufacturer's tested flow data.