Butterfly Valve Cv Chart by Size

Updated 2026-11-21 · Supreme Valves India · Ahmedabad

The disc of a butterfly valve stays in the flow path when the valve is open, so its Cv is lower than a full-bore ball or gate valve of the same size, but still far higher than a globe valve. The figures on this page are for concentric (resilient-seated) butterfly valves at 90° open.

Quick answer

Calculated Cv for a fully open butterfly valve: 2" ≈ 138, 4" ≈ 554, 6" ≈ 1,340. Cv is the flow of water in US gallons per minute that gives a 1 psi pressure drop. These are calculated estimates; use the manufacturer's datasheet value for final sizing.

Butterfly Valve Cv and Kv table (DN50 to DN600)

Size (NPS)DNBore used (in)KCvKv
2"DN502.0670.855138120
2½"DN652.4690.810203175
3"DN803.0680.810313270
4"DN1004.0260.765554479
5"DN1255.0470.720898776
6"DN1506.0650.6751,3401,160
8"DN2007.9810.6302,4002,080
10"DN25010.0200.4904,2903,710
12"DN30011.9380.4556,3205,460
14"DN35013.1240.4557,6306,600
16"DN40015.0000.32511,80010,200
18"DN45016.8760.30015,50013,400
20"DN50018.8120.30019,30016,700
24"DN60022.6240.30027,90024,200

Basis: K = 45 × fT for 2–8", 35 × fT for 10–14" and 25 × fT for 16–24" (concentric butterfly valve, fully open), with the Crane TP-410 friction factor fT for each size and the Schedule 40 pipe inside diameter as the bore. Values are rounded to three significant figures. Tested values on a manufacturer's datasheet are usually lower, because seat rings, port shape and body geometry add resistance.

How the values are calculated

Cv = 29.9 × d² ÷ √K   (d = bore in inches)
Kv = 0.865 × Cv

K is the resistance coefficient of the fully open valve. Crane Technical Paper 410 expresses it as a multiple of the pipe friction factor fT, which lets one formula cover every size. If you know the actual seat bore of the valve you are buying, put that diameter into the formula instead of the Schedule 40 figure.

Pressure drop through a butterfly valve

ΔP (psi) = SG × (Q ÷ Cv)²   (Q in US gpm)
ΔP (bar) = SG × (Q ÷ Kv)²   (Q in m³/h)

Example: water (SG 1.0) at 400 US gpm through a 4" butterfly valve with Cv 554 gives ΔP = (400 ÷ 554)² ≈ 0.52 psi. In metric units, 90 m³/h through the same valve (Kv 479) gives about 0.035 bar.

Pressure-drop and required-Cv calculator (liquids)

What changes the Cv of a real butterfly valve

Send line size, class, fluid, flow and allowable pressure drop. We reply with a matched butterfly valve offer and datasheet.

Contact / RFQ WhatsApp

FAQ

What is the Cv of a 4 inch butterfly valve?

Calculated for a concentric valve, fully open, a 4 inch (DN100) butterfly valve has a Cv of about 554 (Kv about 479). The value depends on disc design, so use the manufacturer's figure for final sizing.

Does butterfly valve Cv change with opening angle?

Yes. The published Cv is at 90° (fully open). Cv drops steeply as the disc closes, so throttling calculations need the manufacturer's Cv at the actual opening angle.

Is the Cv of a triple-offset butterfly valve the same as a concentric one?

No. Offset designs have a thicker disc and an offset shaft in the flow path, so their fully open Cv is lower than a concentric valve of the same size.

How do I calculate pressure drop across a butterfly valve?

For liquids, pressure drop in psi = SG × (Q ÷ Cv)², with Q in US gallons per minute. In metric units, pressure drop in bar = SG × (Q ÷ Kv)², with Q in m³/h.

Related charts

Globe valve Cv chart · Gate valve Cv chart · Ball valve Cv chart · Master Cv chart · Cv to Kv conversion · Valve pressure-drop calculator · Butterfly valves · Quote from Cv sizing

Reference: Crane Co., Technical Paper No. 410, Flow of Fluids Through Valves, Fittings and Pipe. This page is an engineering aid, not a substitute for the valve manufacturer's tested flow data.