Power Plant Valve Application Matrix — BFP, Steam Drain, CW & Utility

Updated 2026-11-08 · Thermal / captive power and large industrial steam plant screening. OEM and EPC line lists override this matrix.

Direct answer · Power plant valve matrix

BFP → high-Class gate/globe + check + min-flow control on discharge; large isolation + strainer on suction. Steam drains → gate/globe + strainer + trap train (IBR as applicable). CW → large butterfly / gate, low Class, actuator torque critical. Utilities → Class 150 / PN16 ball, butterfly, gate, globe per fluid. Quote by tag, service, size, Class, MOC, ends.

Power RFQ — tag · service · size · Class · MOC · ends · actuator · qty.

Contact / RFQ WhatsApp

Power and large captive plants mix ultra-high-pressure feedwater with low-pressure cooling water on the same BOQ. This matrix keeps the four most common contractor enquiry buckets — BFP, steam drain, CW, utility — aligned to typical valve types, Class bands and materials so RFQs stop mixing Class 150 CW butterflies with Class 1500 feedwater gates under one vague “power plant valves” line.

Master application matrix

ServiceTypical valve typesClass / PN screenMOC screenNotes
BFP suctionGate, butterfly, foot valve (if), strainer150–300 / PN16–40WCB / DI / SSNPSH / strainer ΔP
BFP discharge isolationGate / parallel slide / globe600–2500WCB / WC6 / WC9 / F91Per steam cycle
BFP discharge checkSwing / piston / nozzle checkMatch dischargeMatch lineSlam / damper
BFP recirculation / min flowGlobe / control / automatic recirculationMatch dischargeHard trimOEM package often
Main / HP steamGate, globe, check600–2500Alloy steelsIBR / OEM
Steam drain / dripGate, globe, strainer, trapMatch headerWCB / alloySee trap chart
BlowdownAngle BDV / tandemMatch boilerHard-facedSee BDV chart
CW supply / returnButterfly, gate, knife gatePN10/16 / 150DI / CS / lined / seawater alloyLarge DN, actuators
CW pump discharge checkSwing / dual-platePN10/16Match CWWater hammer
Service / potable waterGate, butterfly, ballPN10/16DI epoxy / brass / SSPotable approvals if any
Instrument / plant airBall, needle, filter-regPN16 / 150Brass / SS / CSOil-free if specified
Fire waterGate OS&Y, butterfly + tamper where listedPN16 / 150DI / WCBListing if fire code
LP condensateGate, globe, check, ball150 / PN16–40WCB / CF8Flash risk on HP drains
Chemical dosingDiaphragm / ball / needlePer packageCompatible alloy / linedCorrosion Spec

BFP (boiler feed pump) detail

LocationFunctionPreferred typeRFQ flags
Suction isolationPump take-outGate / butterflyGear on large DN
Suction strainerDebrisTemporary / permanent basket or YMesh + ΔP taps
Discharge isolationBlockGate / parallel slideHigh Class; BW ends common
Discharge NRVPrevent reverseCheck (type per OEM)Slam analysis
Warm-up / bypassThermalGlobe small boreForged SW/NPT
Min-flow recirculationProtect pumpControl / ARC valveOften OEM skid
Drains / ventsFill / ventGlobe / needleTag separately

Feedwater chemistry and oxygen scavenging can drive stainless trim even on carbon-steel bodies. State deaerator pressure, BFP shutoff head and design temperature — Class alone is not enough.

Steam drain & drip-leg train

ComponentTypeTypical sizeComment
Upstream isolationGate OS&YDN15–50Match steam Class
StrainerY-type SS screenMatch80–100 mesh common
TrapTD / bucket / F&TPer loadSee trap chart
Downstream isolationGate / globeMatchChange-out
Test / drainGlobe / needleDN15Safe discharge
Check (if needed)Piston / swingMatchReturn backflow

Circulating water (CW) & cooling

DutyValve preferenceActuationMOC / lining
CW pump isolationButterfly / gateGear / electricDI epoxy / CS
CW pump checkSwing / dual-plate—Match CW Spec
Condenser inlet / outletButterfly large DNElectric / hydraulicOften rubber seated
Cooling tower basinButterfly / knife gateManual / electricCorrosion Spec
Seawater CWButterfly / lined / alloyAs SpecNAB / Duplex / lined DI
Auxiliary CWButterfly / ball / gateManualDI / WCB

CW RFQs fail most often on missing torque / actuator data and missing lining Spec. Include ΔP, velocity and water chemistry.

Utility systems quick matrix

UtilityCommon valvesClass screenEnds
Plant / instrument airBall, needle, filter150 / PN16NPT / SW / RF
Nitrogen / inertBall, globe150–300SW / RF
Demin / condensate polishButterfly, diaphragm, ballPN10/16RF / wafer
Fuel oil (light)Ball, gate, globe150–300RF / SW; fire-safe if Spec
Fire waterOS&Y gate, listed butterflyPN16 / 150RF / grooved if Spec
Drainage / effluentKnife gate, butterfly, ballPN10Wafer / RF

Operation & actuation screening

Size / dutyManualGearActuated
≤DN50 low ClassHandwheel / leverRareIf remote
DN65–200HandwheelOftenIf ESD / remote
≥DN250 CW / large steam—CommonElectric / pneumatic / hydraulic
High-Class HP feedwaterGear even on mid sizesYesMotor on critical isolation

Documentation package by service band

BandTypical docs
HP steam / BFP discharge3.1 MTC, GA, hydro chart, IBR if applicable, PMI if Spec
Steam drain station3.1, trap capacity sheet, strainer mesh note
CW large butterflyTorque sheet, actuator datasheet, lining Spec, coating
Utility3.1 or 2.2 per purchaser; hydro per API 598 / EN 12266

FAQ

What valve types are typical on BFP suction and discharge?

Boiler feed pump (BFP) suction often uses large gate or butterfly isolation with suction strainer; discharge uses high-Class gate/globe isolation, non-return (check) valves, and recirculation/minimum-flow control valves per OEM. Ratings follow feedwater design pressure — commonly Class 600–2500 depending on plant steam conditions.

Which valves are used on steam drain lines?

Steam drain and drip legs typically use gate or globe isolation, Y-strainers, steam traps, and sometimes dual isolation with a drain globe. Class and MOC follow the steam header; see the IBR steam rating and steam trap charts.

What is common for circulating water (CW) valves?

CW and cooling-water systems use large butterfly (often rubber-lined or metal-seated), knife gate or gate valves, with DI/CS/epoxy or seawater alloys as specified. Pressure is usually low (PN10/PN16 / Class 150) but sizes are large — torque and actuator duty dominate the RFQ.

Are utility valves the same Class as main steam?

No. Instrument air, service water, fire water and LP condensate utilities are usually Class 150 / PN16 or lower. Always take Class from the line list, not from the nearest main-steam Class.

What should a power-plant valve RFQ include?

Tag, service (BFP/steam drain/CW/utility), size, Class/PN, MOC, ends, operation (manual/gear/actuator), design P/T, fluid, IBR if steam, test standard, quantity and any NACE/coating notes.

Related charts

Application screening for 2026 EPC and plant enquiries. Freeze selections on the purchaser line list, OEM manuals and current ASME / API / IBR editions.