Gasket Selection Chart (RF Spiral Wound / CAF / PTFE / RTJ)

Updated 2026-11-08 · Screening matrix — freeze on piping class + gasket maker TDS.

Direct answer · Which gasket?

Match gasket to facing + service + class + temperature: CAF/CNAF for mild RF utility; PTFE for corrosive / clean chemical RF within temp limits; spiral wound for most process / steam RF Class 150–600; RTJ metal ring for RTJ-faced Class 600+ hydrocarbon and high-integrity lines.

Ordering flanged valves? State facing (RF/RTJ) · class · MOC · service · qty.

Contact / RFQ WhatsApp

This chart is for piping engineers and contractors screening gasket families against valve flange facings. It is not a chemical-compatibility encyclopedia — confirm media, fire-safe requirements and seating stress with the gasket manufacturer and the project piping class.

Selection matrix by service

ServiceTypical facingPreferred gasket familyAvoid / caution
Cooling / potable / utility waterRF (Class 150 / PN16)CAF / CNAF or EPDM (where soft gasket allowed)Graphite spiral wound overkill unless class sheet requires
Instrument / plant airRF Class 150CAF / CNAF or PTFERTJ unnecessary
Corrosive chemicals / acids (clean)RF SS flangesPTFE / filled PTFE (within temp)CAF swelling; check media list
Saturated / superheated steamRF Class 150–300+Spiral wound (graphite fill)Virgin PTFE cold flow; soft CAF at high T
Hydrocarbons / process (moderate)RF Class 150–300Spiral wound graphite / SSCAF if fire / cyclic risk high
Hydrocarbons high pressureRTJ Class 600+Soft iron / SS / Inconel ring (per class)Do not put spiral wound on RTJ groove
Hot oil / thermal fluidRFSpiral wound graphitePTFE temp limit
CryogenicRF / specialProject-specified (often spiral / PTFE filled)Standard CAF embrittlement
Fire-safe hydrocarbonRF or RTJGraphite spiral wound or RTJ metalElastomer / virgin PTFE alone

Gasket family comparison

FamilyFacingTypical class bandTemp cue (screening)StrengthWatch-out
CAF / CNAF (compressed fibre)RF / FF*PN10–16 / Class 150 utilityOften ≤ ~250–400°C by gradeLow cost, easy stockCreep, steam, cyclic, fire
PTFE / filled PTFERFClass 150–300 chemicalVirgin PTFE often ≤ ~200–260°CChemical inertnessCold flow; needs controlled stress
Spiral wound (SS + graphite)RF (inner/outer rings as specified)Class 150–600 RF processGraphite often to ~450–550°CCycling, steam, hydrocarbonWrong ring OD; over-torque crush
RTJ metal ring (R / RX / BX)RTJ groove onlyClass 600–2500 typicalMetal ring — match ring MOCHigh integrity sealRing number must match groove

*Flat-face (FF) soft gaskets are common with cast-iron / brittle flanges. Do not mate RF to FF without engineering check. See RF vs RTJ chart.

Facing → gasket quick map

Valve / flange facing on RFQGasket to planWhat to write on BOQ
ASME B16.5 Class 150 RFCAF or spiral wound per class sheet“Class 150 RF + spiral wound / CAF as per piping class”
ASME B16.5 Class 300 RFSpiral wound preferred for process“Class 300 RF + SWG + outer ring (if required)”
ASME B16.5 Class 600 RFSpiral wound (confirm)“Class 600 RF + SWG”
ASME B16.5 Class 600 RTJMetal ring (R-number)“Class 600 RTJ + ring no. R-XX, MOC …”
EN 1092-1 PN16 RF / Type BCAF or SWG per EN / project“PN16 RF + gasket to EN class sheet”

Common mistakes

MistakeResultFix
Spiral wound on RTJ flangeWill not sealMetal ring only in RTJ groove
PTFE on high-temp steamBlow-out / cold flowSpiral wound graphite
Wrong spiral OD / inner ringBore intrusion or leakMatch NPS, class, RF dimensions
Reusing crushed CAFWeep after hydroNew gasket every break
Ignoring fire-safe noteSpec non-complianceGraphite SWG or RTJ per class

Screening data only. Media compatibility, m & y (or gasket constants), fire test and dimensions must come from the current gasket manufacturer TDS and the purchaser piping specification. Interactive helper: gasket material selector.

FAQ

When should I use a spiral-wound gasket instead of CAF?

Use spiral wound (typically graphite-filled, SS winding) for higher temperature, thermal cycling, steam and most Class 300+ RF hydrocarbon/process lines. CAF/CNAF suits mild water/air utility at moderate temperature when the piping class allows.

Can PTFE gaskets be used on steam?

Standard virgin PTFE is limited by cold flow and temperature. Prefer filled PTFE grades only within maker limits, or switch to spiral wound / RTJ for steam. Always check the gasket datasheet.

Does the valve RFQ need the gasket type?

Yes when facing is RTJ (ring number) or when the purchaser specifies gasket with the valve package. For RF valves, gasket is often a piping bulk item — still state facing clearly.

Related charts