Raised Face vs RTJ Flange Chart (When to Use)

Updated 2026-11-08 · Screening reference — match the piping class sheet before purchase.

Direct answer · RF or RTJ?

Raised face (RF) is the default for most Class 150/300 process and utility valves with CAF, PTFE or spiral-wound gaskets. RTJ (ring-type joint) is used when the piping class demands a metal ring seal — typically Class 600+ hydrocarbon / high-pressure gas. Never mix RF and RTJ on the same joint.

Quote flanged valves with facing stated: RF or RTJ · size · class · MOC · qty.

Contact / RFQ WhatsApp

Facing is a purchase-critical field on every flanged valve RFQ. Wrong facing means the valve will not mate to the piping flange — scrap or expensive rework. Use the charts below for contractor screening; freeze facing from the approved piping class.

When-to-use chart

SituationPreferWhyGasket
Utility water, air, HVAC (Class 150 / PN16)RFLow cost, easy maintenanceCAF / CNAF / soft gasket
General process Class 150–300RFIndustry defaultSpiral wound or CAF per class
Steam Class 150–300RFSWG handles heat / cycleSpiral wound graphite
Class 600 utility / lower severityRF (if class allows)Still common on some plantsSpiral wound
Class 600+ hydrocarbon / gasRTJMetal ring integrityR / RX ring (number match)
High-integrity / sour / critical isolationRTJ (if specified)Piping class / owner preferenceRing MOC per NACE / class
Cast iron / brittle companion flangesFF (not RF)Avoid bending moment on RFFull-face soft gasket
Unknown — only “flanged” on BOQAskDo not guess facingHold RFQ until clarified

RF vs RTJ comparison

TopicRaised face (RF)Ring-type joint (RTJ)
Seal elementSoft / semi-metallic gasket on raised faceMetal ring in machined groove
Typical classes150, 300, many 600 RF600, 900, 1500, 2500
Assembly skillStandard flange crewGroove/ring cleanliness critical
Reuse after breakNew gasket alwaysOften new ring; inspect groove
Mis-mate riskRF to FF dangerous without checkRF to RTJ will not work
RFQ must include“Class xxx RF”“Class xxx RTJ” + ring no. if known

Class cue (screening — not a rule)

ASME classCommon facing on valvesContractor note
Class 150RF (dominant)RTJ rare unless special
Class 300RF (dominant)RTJ only if piping class says so
Class 600RF or RTJConfirm — hydrocarbon often RTJ
Class 900 / 1500 / 2500RTJ typicalState ring groove / ring number

RFQ wording examples

NeedWrite thisDo not write
Utility gate4" ASME B16.5 Class 150 RF, WCB4" flanged gate (facing blank)
Process globe2" Class 300 RF, CF8M, spiral-wound lineClass 300 flanged (RF assumed)
Pipeline ball8" Class 600 RTJ, ring R-49 (example), A105/LF2Class 600 RF when isometrics show RTJ
Metric waterDN 150 EN 1092-1 PN16 Type B RFDN 150 Class 150 (mixed standards)

Ring numbers in examples are illustrative only — use the ring schedule from ASME B16.20 / piping class. Also see gasket selection chart, Class 600 dimensions and end connection chart.

FAQ

Can I mate an RF flange to an RTJ flange?

No. Raised-face and ring-type-joint facings are not interchangeable. The gasket systems differ and the flanges will not seal correctly.

When is RTJ preferred over raised face?

RTJ is preferred on many Class 600 and higher hydrocarbon, high-pressure gas and high-integrity lines where the piping class calls for a metal ring seal.

What must the valve RFQ say for facing?

State RF or RTJ explicitly with class. For RTJ also state ring number / groove standard when known so the valve flange matches the piping.

Related charts