Does Class 600 share the same bolt circle as Class 300?
Through NPS 3½, Class 300 and Class 600 share the same OD and bolt pattern. From NPS 4 upward, Class 600 uses a larger OD, different PCD and often larger bolts.
Updated 2026-11-08 · Screening reference — confirm against the current ASME B16.5 edition before IFC.
Direct answer · Class 600 flange chart
Millimetre values below are engineering screening figures commonly used by piping contractors. Hub length, flange thickness, raised-face height and RTJ groove dimensions also matter — freeze design on the purchaser datasheet and the current ASME B16.5 tables.
Complement to the Class 150 & 300 flange dimensions chart. For facing selection see RF vs RTJ chart.
| NPS | DN | Flange OD (mm) | Bolt circle PCD (mm) | No. of bolts | Bolt size |
|---|---|---|---|---|---|
| ½" | 15 | 95.3 | 66.7 | 4 | ½" |
| ¾" | 20 | 117.5 | 82.6 | 4 | ⅝" |
| 1" | 25 | 124.0 | 88.9 | 4 | ⅝" |
| 1¼" | 32 | 133.4 | 98.4 | 4 | ⅝" |
| 1½" | 40 | 155.6 | 114.3 | 4 | ¾" |
| 2" | 50 | 165.1 | 127.0 | 8 | ⅝" |
| 2½" | 65 | 190.5 | 149.2 | 8 | ¾" |
| 3" | 80 | 209.6 | 168.3 | 8 | ¾" |
| 3½" | 90 | 228.6 | 184.2 | 8 | ⅞" |
| 4" | 100 | 273.1 | 215.9 | 8 | ⅞" |
| 5" | 125 | 330.2 | 266.7 | 8 | 1" |
| 6" | 150 | 355.6 | 292.1 | 12 | 1" |
| 8" | 200 | 419.1 | 349.3 | 12 | 1⅛" |
| 10" | 250 | 508.0 | 431.8 | 16 | 1¼" |
| 12" | 300 | 558.8 | 489.0 | 20 | 1¼" |
| 14" | 350 | 603.3 | 527.1 | 20 | 1⅜" |
| 16" | 400 | 685.8 | 603.3 | 20 | 1½" |
| 18" | 450 | 743.0 | 654.1 | 20 | 1⅝" |
| 20" | 500 | 812.8 | 723.9 | 24 | 1⅝" |
| 24" | 600 | 939.8 | 838.2 | 24 | 1⅞" |
| Size range | OD / PCD vs Class 300 | Practical note |
|---|---|---|
| NPS ½–3½ | Same OD and bolt pattern as Class 300 | Flange thickness and hub differ — do not mix ratings on the same joint |
| NPS 4 and above | Class 600 OD and PCD are larger; more / larger bolts | Class 300 and Class 600 flanges will not bolt up |
| Facing | RF common; RTJ frequent on Class 600 hydrocarbon | State facing + ring number (if RTJ) on the RFQ |
| Field | What to write |
|---|---|
| Standard / rating | ASME B16.5 Class 600 |
| Facing | RF or RTJ (with ring groove / ring number if RTJ) |
| MOC | WCB, CF8M, LF2, etc. as per piping class |
| Size / qty | NPS or DN + quantity |
| Gasket / bolting | Spiral wound / RTJ ring + stud grade if purchaser-specified |
Screening data only. Thickness, raised-face height, RTJ groove and bolt-hole diameter must be taken from the current ASME B16.5 edition or the approved isometrics — not from this page alone.
Through NPS 3½, Class 300 and Class 600 share the same OD and bolt pattern. From NPS 4 upward, Class 600 uses a larger OD, different PCD and often larger bolts.
Many hydrocarbon and high-integrity Class 600 lines specify RTJ. Utility and lower-severity Class 600 may still use raised face with spiral-wound gaskets. Match the piping class sheet.
Yes. State NPS, Class 600, facing (RF or RTJ), MOC and quantity on the RFQ.